Standard

Replacement:
This part 2 of IEC 61558 applies to stationary or portable, single-phase or polyphase, aircooled separating transformers, associated or not, having a rated supply voltage not exceeding 1000 V a.c., a rated frequency not exceeding 500 Hz, and a rated output not exceeding: . 1 kVA for single-phase transformers; . 5 kVA for polyphase transformers.

Replacement:

This International Standard deals with all aspects of safety such as electrical, thermal and mechanical.

This part 2-13 of IEC 61558 applies to stationary or portable, single-phase or polyphase, aircooled (natural or forced), independent or associated auto-transformers, having a rated supply voltage not exceeding 1 000 V a.c., a rated frequency not exceeding 500 Hz.

Replacement:
This part 2-2 of IEC 61558 applies to stationary or portable, single-phase or poly-phases, aircooled control transformers associated or otherwise having a rated supply voltage not exceeding 1 000 V a.c. or 1 415 V ripple free d.c. and rated frequency not exceeding 500 Hz and no limitation of the rated output.
This standard is applicable to transformers used between circuits where double or reinforced insulation is not required by the installation rules or by the equipment specification.

Replacement:
This part 2 of IEC 61558 applies to stationary or portable, single-phase or polyphase, air-cooled isolating transformers, associated or otherwise, having a rated supply voltage not exceeding 1000 V a.c. and rated frequency not exceeding 500 Hz, the rated output not exceeding: - 25 kVA for single-phase transformers; - 40 kVA for polyphase transformers.

Replacement:
This part 2 of IEC 61558 applies to stationary or portable, single-phase or polyphase, aircooled safety isolating transformers, associated or otherwise, having a rated supply voltage not exceeding 1000 V a.c. and rated frequency not exceeding 500 Hz, the rated output not exceeding: - 10 kVA for single-phase transformers; - 16 kVA for polyphase transformers.

This is the harmonized CSA Group and UL standard for General Requirements for Battery-Powered Appliances. It is the first edition of CSA C22.2 No. 0.23, and the second edition of UL 2595. This edition of UL 2595 supersedes the previous edition published on May 22, 2013.
Scope:

Preface:
This is the third edition of CSA C381.2, Energy performance of battery-charging systems and uninterruptible power supplies. It supersedes the previous editions published in 2014 and 2008 under the title, Test method for determining the energy efficiency of battery-charging systems.
This Standard specifies requirements, definitions, and test methods for determining the energy performance of battery-charging systems.
Scope:

This part of the IEC 61427 series gives general information relating to the requirements for the secondary batteries used in photovoltaic energy systems (PVES) and to the typical methods of test used for the verification of battery performances. This part deals with cells and batteries used in photovoltaic off-grid applications.
NOTE The part 2 of this series will cover cells and batteries used in "renewable energy storage in on-grid applications".

This part of IEC 60896 is applicable to lead-acid cells and batteries which are designed for service in fixed locations (i.e. not habitually to be moved from place to place) and which are permanently connected to the load and to the d.c. power supply. Batteries operating in such applications are called "stationary batteries".



Any type or construction of lead-acid battery may be used for stationary battery applications. This part 11 of the standard is applicable to vented types only.



The object of this standard is to specify general requirements and the main characteristics, together with corresponding test methods associated with all types and construction modes of lead-acid stationary batteries, excluding valve-regulated types.



Recommendations on the use of tests for stationary battery application are given in Table A.1.



Recommendations relating the type of cell or monobloc to the use of tests are given in Table A.2.



Statements and claims of basic performance data by the manufacturer shall correspond to those tests.



The tests may also be used for type qualification. 

This part of IEC 60896 applies to all stationary lead-acid cells and monobloc batteries of the valve regulated type for float charge applications, (i.e. permanently connected to a load and to a d.c. power supply), in a static location (i.e. not generally intended to be moved from place to place) and incorporated into stationary equipment or installed in battery rooms for use in telecom, uninterruptible power supply (UPS), utility switching, emergency power or similar applications.