Code

The IMC regulates the design, installation, maintenance, alteration and inspection of mechanical systems that are permanently installed and utilized to provide control of environmental conditions and related processes within buildings. It also regulates those mechanical systems, system components, equipment and appliances specifically addressed herein. The installation of fuel-gas distribution piping and equipment, fuel gas-fired appliances and fuel gas-fired appliance venting systems shall be regulated by the International Fuel Gas Code.

The IPC applies to the erection, installation, alteration, repairs, relocation, replacement, addition to, use or maintenance of plumbing systems within this jurisdiction. This code shall also regulate non-flammable medical gas, inhalation anesthetic, vacuum piping, nonmedical oxygen systems and sanitary and condensate vacuum collection systems. The installation of fuel-gas distribution piping and equipment, fuel-gas-fired water heaters and water heater venting systems shall be regulated by the International Fuel Gas Code.

The provisions of the IWUCl apply to the construction, alteration, movement, repair, maintenance and use of any building, structure or premises within the wildland urban-interface areas in this jurisdiction. Buildings or conditions in existence at the time of the adoption of this code are allowed to have their use or occupancy continued, if such condition, use or occupancy was legal at the time of the adoption of this code, provided such continued use does not constitute a distinct danger to life or property.

This Code covers basic provisions for safeguarding of persons from hazards arising from the installation, operation, or maintenance of conductors and equipment in electric supply stations and overhead and underground electric supply and communication lines. It also includes work rules for the construction, maintenance, and operation of electric supply and communication lines and equipment. The standard is applicable to the systems and equipment operated by utilities, or similar systems and equipment, of an industrial establishment or complex under the control of qualified persons.

NFPA 400 consolidates fundamental safeguards for the storage, use, and handling of hazardous materials in all occupancies and facilities. The Code does not apply to storage or use of hazardous materials for individual use on the premises of one- and two-family dwellings.

1.1.1 The scope includes, but is not limited to, the following: (1) Inspection of permanent and temporary buildings, processes, equipment, systems, and other fire and related life safety situations (2) Investigation of fires, explosions, hazardous materials incidents, and other related emergency incidents (3) Review of construction plans, drawings, and specifications for life safety systems, fire protection systems, access, water supplies, processes, hazardous materials, and other fire and life safety issues (4) Fire and life safety education of fire brigades, employees, responsible parties

A.1.1 The following is a suggested procedure for determining the Code requirements for a building or structure: (1) Determine the occupancy classification by referring to the occupancy definitions in Chapter 6 and the occupancy Chapters 12 through 42. (See 6.1.14 for buildings withmore than one use.) (2) Determine if the building or structure is new or existing. (See the definitions in Chapter 3.) (3) Determine the occupant load. (See 7.3.1.) (4) Determine the hazard of contents. (See Section 6.2.) (5) Refer to the applicable occupancy chapter of the Code, Chapters 12 through 42.

A.1.1 The Code does not address features that solely affect economic loss to private property. 1.1.1 General. The Code addresses those construction, protection, and occupancy features necessary to minimize danger to life and property. 1.1.2 Code Title. The provisions of this document shall constitute and be known as NFPA 5000, Building Construction and Safety Code, hereinafter referred to as “this Code” or “the Code.”

This Code sets the minimum conditions that a distributor must meet in carrying out its obligations to distribute electricity under its licence and the Energy Competition Act, 1998. Unless otherwise stated in the licence or Code, these conditions apply to all transactions and interactions between a distributor and all retailers, generators, distributors, transmitters and consumers of electricity who use the distributor’s distribution system.

The National Building Code of Canada 2015 (NBC), published by NRC and developed by the Canadian Commission on Building and Fire Codes, sets out technical provisions for the design and construction of new buildings. It also applies to the alteration, change of use and demolition of existing buildings. Over 360 technical changes have been incorporated in this new edition.